How To Change A LiPo Connector On A LiPo Battery Safely
6,104
Published 2023-10-18
This example is shows changing the connector on a LiPo battery, which is usually the most difficult due to the high short protentional if you don't know what you're doing; but the same process would be followed if you have to change the LiPo connector on an ESC / similar.
Time Chapter Index:
0:00 Intro
1:54 Removing Old Connector
3:59 Soldering Tools Used
5:40 Soldering Tips & Tricks
6:42 Fitting New LiPo Connector
12:42 Conclusion
Link to my RC Connector page:
www.rchelicopterfun.com/rc-battery-connector.html
Link to my RC Soldering For Beginners page:
www.rchelicopterfun.com/rc-soldering.html
Product Links:
Weller 9400 Soldering Gun
amzn.to/3M5TuFP
T12 Soldering Station
amzn.to/3FkC58E
D4 T12 Soldering Tip
amzn.to/3QkCpua
Kester 44 60/40 Rosin Core Solder
amzn.to/3FnlIby
XT90 Connector Set
amzn.to/45yvQsj
Gens Ace LiPo Batteries
www.buddyrc.com/collections/gens-ace-batteries?ref…
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you!
Thank you for supporting RC Helicopter Fun.com & my channel which helps me keep creating content & showing fun projects like this. Please consider giving a thumbs up & subscribe if you enjoy the content - thank you & thanks for watching :)
All Comments (21)
-
Want more RC Connector & Soldering Information? Link to my RC Connector page: www.rchelicopterfun.com/rc-battery-connector.html Link to my RC Soldering For Beginners page: www.rchelicopterfun.com/rc-soldering.html
-
You make it look so easy, I always watch your videos even though I'm no into RC hobby, there's always new tips I can pick up along the way.
-
Hi dude, I was due to replace some gnb27 connectors with some a30 ones. They are infinitely smaller, but the same principle is used. Thanks for sharing! 😊
-
Great video. Soldering is comforting for me. I switched from EC5 TO XT90. I pretty much do what you do, but i love the vise technique which i will adopt. 😊
-
Teknik solder yang sangat bagus, saya suka.
-
Very good video John, I have never seen it done like this.
-
Good video.
-
I just cut the connector shell and the bullet pins come right out.Than incert them into the connector you want I did this and it worked fine.
-
Great video John - thank you.
-
Very nicely done and explained; thanks!
-
Put a temporary strip of kapton tape across the back of the cup before soldering then if you have any spillage it just runs off and won't stick. Also have you seen the QS8 connectors yet? They're basically an enlarged XT90.
-
This is one task that can totally ruin your day if you don't take your time and prevent a short at all costs. It happened to me once. The spark is bad enough, but the really dangerous part is if it welds itself to the other lead. If you can't rapidly separate them, it's like holding a hand grenade after you lost the pin and spoon. I was fortunate and was able to separate them but in that short time the battery became very hot, and one cell was smoked. I do like the new solderless connectors that have come out and have been converting my packs over. Either way, be extra careful.
-
Xt90 for the win!
-
Very interesting as always ! Where are you installing/using those new batteries?
-
Great video john on another note will you be changing to Edgetx
-
Any R2 updates ? how are the parts holding up and are the seams starting to show cracks in the paint ? any events with the droid ?
-
Though you can plug ec5 into xt90 if you are lazy
-
I have a cheap soldering iron i never soldered before it says 120v+25% 60 watt will that work for these connectors
-
Hi! I have an old lipo (going to trash) And a new with not T plug If i remove the T plug from the old one can i put the old lipo in "trash" if it dont have any plug just the cutted cable? Or should i put the other type plug on it what i dont need? - thanks!
-
Just a heads up doing this does void your warranty I messaged gens ace just to be sure.