Holzbefeuerte Poolheizung|Wood-fired Poolheater|Alles.Handarbeit
1,063,094
Published 2021-08-13
In this video I am building a wood-burning pool heater. You can see what temperatures they bring at the end of the video. Anyway, I was surprised.
Zu meinem Kanal geht es hier:youtube.com/c/AllesHandarbeit
Meine Maschinen:
Metalltrenner: Güde GMT 355
Plasmaschneider: Berlan BPS 40
Schweißgeräte: NTF MIG 250, NTF TIG 160 PD, Elektra Beckum Trafo
Bandsäge: Güde MBS 125 V
Säulenbohrmaschine: Rotwerk EBT 1609
Drehbank: Bernado Profi 550 WQ
Winkelschleifer: Diverse,115,125,230 mm
Druckluftnagler: Güde 40220
Einhandschleifer: Güde 40032
Rundbiegegerät: Eigenbau
Bandschleifer: 50 X 2000mm Eigenbau
Radienbiegegerät: Eigenbau
Handbohrmaschinen: Diverse
Akkuschrauber: Meister
All Comments (21)
-
Danke für das neue Video, war wieder sehr unterhaltsam.
-
very nice place to work also, good equipment and tools
-
Schönes altes Prinzip . Ich bin bei meiner Arbeit in alten Hamburger Häusern öfter mal Holz- oder kohle-befeuerten Durchlauferhitzern aus Kupfer begegnet . Die stammten so aus der Zeit um den 2. WW herum .
-
Works well, you can feel the warmer water coming back into the pool after running through the mat. Wish the inlet/outlet ports were adjustable, but overall, a good and efficient way to raise the water temp.
-
Richtig geil gemacht 👍👍👍
-
An alternative to separating the coil from the walls for better heat distribution, as another user commented below would be isolating the external part of the tank with some kind of rock wool, styrofoam or some other expanding foam, then another layer to encase the whole thing like a bigger tank or using retractary cement basically turning it into an oven.
-
I like your work I hope more beautiful videos upload
-
Tolle Fahrstuhlmusik
-
Interessante Idee!
-
oben Edelstahlplatte, Rundgrill. Top Idee!
-
Super Sache 👍 Die Temperatur sieht wirklich sehr gut aus. Da dürfte der Pool je nach Größe recht schnell warm werden. Grüße
-
Great build man
-
For higher heat transfer efficiency and improved pump GPM. Use three parallel separate coils with inlet and outlet headers and keep the copper coils at least 1 inch away from the barrel wall.:yougotthis:
-
Wow wenn man jetzt noch chlor und kupfer bei google eingibt merkt man was für ne tolle Idee das ist:D
-
Nice idee, Most off the heat will go tru the chimnee means youre water will be much more hotter than placing pipe‘s around the barrel. If it starts at the downside with a backvalve out side the barrel and ends in the top of a chimnee, You will not need a pump, it will be like a coffee machine, with constant running hot steam water.
-
den fehler hab ich auch mal gemacht, viel zu viel wicklungen und abstand zu klein, abstand sollte ca. 1,5 mal rohrdurchmesser haben dann wird die ganze oberfläche vom rohr heiß, nicht nur ein teil.
-
Thank you
-
Perfect 👍👍👍👍
-
Would this work with 2 barrels, 1 containing the coils and the other used as firebox? Connected with chimney pipe and then a vent from the coil barrel. I have a lot of water to heat.
-
Gut gemeint ,viel Arbeit gemacht, ob das ganze dann effektiv ist werden wir evtl. irgendwann erfahren. Ich hatte mal vor Jahren einfach einen alten Badeofen (war in den 60er Jahren Standard) umfunktioniert , statt der Mischbatterie nur Zu und Ablauf drangeschraubt, den Kessel dann außenrum mit Steinwolle isoliert und Feuer frei. Die 100 Liter waren so schnell warm/heiß ♨,mit wenig Holz. eine kleine Bachlaufpumpe hat den Rest erledigt. Die Effektivität war kaum zu überbieten.