10KW Free Power Generator With Microwave Parts - Liberty Engine 3.0 - 100% REAL

Самое сложное в этой конструкции, это спрятать питающий сетевой провод, с чем автор справился отлично!!!

Whats amazed me is that so many people think this is genuine. Speechless ...

That's absolutely genius. The thing that's even more genius is that there are no moving parts.

fantastic video the tube inside, what material is it made of and wheels for ignition if we inserted a 220 volt plug it would still start waiting for you greetings mike

the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator. To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous. May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents. But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system) A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator). The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar. So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).

To which terminals do we connect the socket for the starting impulse? At the voltage input or the voltage output?

hello sir, how to stop the generator? from producing the current

I’m really liking your compact direction😅

Пока полной чистоты не будет, это лишь красивый фокус. Поднять всю установку в руки и включить мощную нагрузку и носить на руках на камеру со всех сторон. Until there is complete cleanliness, this is just a beautiful trick. Lift the entire installation in your hands and turn on a powerful load and carry it on your hands to the camera from all sides.

Я вот почти все понял, вот только не понял как двигатель 0.75квт может на выходе дать 10квт. Наверно все дело в наклейках, главное их надо правильно наклеить.

İlginç, spiral makinesi çalıştığında lambada voltaj düşümü olmuyor. Nükleer tesisten alıyor olmalı şebeke elektriğini?

So nice of you not to patent this technical marvel and make a fortune while solving the energy problems of the world. I'm so touched, my tears are also 100% real. OMG LMAO.

Hi. What is the ratio of silver : aluminum in electro magnet field bar? How much should it weight ? Thank you.

Nice Sir thank you so much ❤❤❤

Beautiful.. and I happen to have all components.. thank you

Hello, does the bar in the center need a specific measurement (size, diameter)? Is this the motor shaft? THANKS

How long the magnet resist?

Здравствуйте Либерти я смотрю все ваши изобретения вы гении своего дела хотелось бы узнать только один ответ что это правда. Я понимаю что секрет остаться за вами и есле это так то вы могли бы помоч миллионам людей сказав правду что это реальность а не фокус

Вы ничего не поняли. Всё дело в стержне, который вставлен вместо ротора! Автор в конфиденциальной переписке сообщил мне, что он изготовлен из материала, предоставленного ему инопланетянами и сейчас он ведет с ними переговоры по организации поставок этого материала на Землю. Так что подождите немного и будет вам счастье! 😄🤣😂

Olá eu também gostari de ver o gerador em funcionamento em uma altura da bancada o ideal ser levando pelas mãos.