Replace SPRINKLER HEAD in 5 Minutes - Rainbird - Hunter - Orbit
1,372,301
Published 2020-06-27
Hori Hori Garden Knife:
amzn.to/3i6DAKI
Sprinkler Head Shown Hunter I-20 Stainless Steel HD Model
amzn.to/2Bhun1E
Hunter PGP Sprinkler Head
amzn.to/2VoAY10
Adjustment Videos
Hunter:
• Adjusting a Hunter Rotor: Rotor Right...
Rainbird 5000
• Rainbird 5000 Sprinkler Adjustment
Orbit Saturn 5
• How To Adjust A Saturn IV Gear Drive ...
K-Rain
• K-Rain® K1 Gear Drive Rotor Sprinkler
Disclaimer:
This video, description & comments may contain affiliate links, which means that if you click on one of the product links I may receive a small commission.
Due to factors beyond the control of Silver Cymbal, I cannot guarantee against improper use or unauthorized modifications of this information. Silver Cymbal assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Silver Cymbal recommends safe practices when working on machines and or with tools seen or implied in this video. Due to factors beyond the control of Silver Cymbal, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Silver Cymbal.
All Comments (21)
-
Thanks for watching I hope this can help you save some money replacing a sprinkler when you need too. I try to always keep one on hand to be ready, Check the description for links to each manufacturers fine adjustments as needed.
-
One of the best "how to" videos I have seen! Well done.
-
I had to replace eight Sprinkler Head today and was very glad I saw your video. The method of using water to create a nice tube to pull the old sprinkler out and slide the new one in WORKED GREAT! Saved a lot of time and digging. Thank you.
-
Great tip about pouring water in the hole before removing the head!
-
This is the video that I needed. I literally dug up some of my sprinkler heads last week to replace them. Definitely following these instructions for the remaining heads. Thanks!
-
Your the best, Your home tips from snow blower to sprinklers is so HELPFUL. Thank you much approach, your great content.
-
I actually used your method today to replace the sprinkler head and it was about five minutes worth of work. The idea of water around the dirt one had came out the other one slid right in tightened up I just had to adjust it. Thank you so much
-
This is by far THE BEST ADVICE. Follow this guys directions. Works very well.
-
Wow, that was easy. Thank you for explaining and demonstrating that.
-
Much simpler than the way I've been doing it. I'll give it a try (and I even have a Hori Hori). Thanks
-
Super good instructions. Easy to understand and follow. Thanks for sharing this.
-
Thanks for this video, very well done. I screwed the adjustment screw up all the out of the head of mine and water was just gushing out. I just needed an easy DIY video to replace it tomorrow
-
I was searching how to adjust sprinklers about 2 days. Only your vid make it right. Thanks!
-
I live in Florida and the ground is mostly sand. That was a great idea of pouring water around the sprinkler. Thanks!
-
Thank you so much for this video. I found the instructions for my Orbit sprinkler absolutely mystifying.
-
Top notch tutorial. Clear and concise. Thank you
-
Fantastic video!! Straight forward and no wasted time. Thanks!!
-
A couple of things I noticed while watching the video: 1) Aligning the right edge. Some heads say to align the left edge. The way you do it is the same, just read the instructions on the replacement head to know which edge to line up. Once this is done, turn the internal adjustment screw to set the other edge while the sprinkler is running. 2) The front adjustment screw doesn't change the flow. The nozzle size does that. The adjustment screw changes the distance that the stream shoots out of the nozzle, not the rate of water flow.
-
FANTASTIC video, very professionally done. Thank you, very much appreciated, God bless !
-
Replaced several last week in my yard. Very easy to do DIY and saves hundreds of dollars.