Making steel sheet Roller Bender machine
3,160,719
Published 2023-01-05
Sheet metal roller bender is a machine that I don't have, so I decided to make it :)
I used a lot of scrap yard stuff so the cost was very low.
Thanks to the use of the motor and gearbox, I was able to resign from the crank, which made the work much faster and more pleasant.
With this tool, I can roll 2 mm thick and about 53 cm wide, which should meet my requirements.
Check out our other workshop tool making videos:
• How to Make Firewood Cutting Machine DIY - How to Make Firewood Cutting Machine DIY
• The easiest way to cut steel - Machin... - The easiest way to cut steel - Machine build DIY
• Welding & Cutting rotary table - BUILD - Welding & Cutting rotary table - BUILD
• Big Vise using Bottle Jack [PLANS] - Big Vise using Bottle Jack [PLANS]
• Electromagnetic Drill press VISE [PLANS] - Electromagnetic Drill press VISE [PLANS]
• Making Lathe MILLING Attachment - Making Lathe MILLING Attachment
All Comments (21)
-
No music, no coments only machine and tools sounds. Perfect!! The best!! Congrats! 👌
-
Urządzenia, które pozwalają na wykonywanie kolejnych, bardziej wymagających urządzeń. Coś pięknego! :)
-
This guy has been killing the asmr game mechanically for years! Always a pleasure to watch
-
Nice job dude!😎
-
One of the best channels on you tube. Please think again on that bad habit of leaving the chuck key in the chuck, bad accident waiting to happen.
-
Дружище с таким инструментом можно за самолёт браться Здорово, завидую по доброму! Удачи Тебе.👍🤝🤝🤝
-
Привет. Я тоже собрал маленький, 550 длина валов в чистоте, на нижних 2 валах подшипники стоят 205,диаметр валов 70мм, на верхнем конусная втулка с одной стороны из латуни. Валы из трубы, не годятся, со временем прогиб будет, конусные с одной стороны, чтоб снимать сваренную обечайку. Не правильно сделал, с одной стороны боковушка сниматься должна, именно в районе верхнего вала, как раз конус в работе, по типу как петли, НЕ ДЕЛО ВАЛ ПОСТОЯННО СНИМАТЬ, посмотрите промышленные вальцы, БОКОВУШКА ОТКИДЫВАЕТСЯ. всем удачи в постройках. 🤝.
-
Great video, I always enjoy watching you create new inventions!
-
You know the fabricator is good when he makes his own tools.
-
Time for a shop tour again. Keep up the good work.
-
Браво мајсторе поздрав из Србије.
-
I'm not sure why you have TWO SWITCHES to make the motor reverse.... but if it work then IT WORKS!!! I LOVE how you make it all look SO DARN EASY!!! You are an AMAZING BUILDER!!! GENIUS!!!
-
I have a factory hand crank roller .. they put gears at the end ,, your setup is good with the slip roller ,, I don't have a slip roller on mine .. only thing I would do is have all the switches on the same side ,, great build
-
Your channel just popped up. Yes, this person is Keith from Michigan USA. I look forward to seeing future projects. I know a few people from Europe. Nice work on this project 🙂. Well, I'm going to bed now. Have a good week....
-
Nice project bro and very effective.
-
On the last roll of the video if you look on the right hand side of your screen you'll see the top middle bar rolling out as you're passing things through , you might consider a screwed on cap that's slightly bigger than the bar or something so that it doesn't roll itself out like that.
-
For Bearing material. Copper based metal bushing provide needed compressive strength for this application and lubricating effect comparable to polymer. Thanks for sharing idea of plate bending machine building.
-
I have a need for a set of rollers - this version's heading to the top of the list ! God knows why commercial ones are so expensive .... ..
-
A Berilliant no nonsense piece of fabrication! Top notch Sir!!
-
Saludos desde Puerto Rico Maestro usted es un genio , lo hace ver demasiado facil pero es por el mega talento que usted tiene, Gracias por compartir su mega talento creativo , se nota que usted Ama fabricar cosas muy utiles ,Tiene la habilidad de fabricar herramientas cosa que no todos tienen, Bendiciones y que logre todas sus metas.
